TCU Codes (Automatic Transmissions) DSMs коды ошибок акпп
Here are the codes for the TCU. These can be obtained by using the same principal for pulling the ECU codes.
I use a multimeter and 2 wires with alligator clips. You can get the clips from Radio Shack or wherever.
Hook up to pins and Set the mulitmeter for 12 V. Turn the key all the way but do not crank (the power windows work in this position). Watch the pulses of the needle (if Analog). Write down L for long and S for short. The TCU will cycle the codes over and over. So you can double check them if needed. If you get constant short pulses, the TCU has no codes and all is well (so it would seem).
Once you write it down, figure L = 10 and S = 1. EX: L-L-S-S=22. GO to the chart below and it will tell you what the code means.
The left is the 1G Diagnostic plug. The right is the 2G.
Red is you hook up the Positive lead of the Meter and Gray is Negative. If it does not work or read, try reversing the leads.
1G hook POS to #6 and NEG to #12.>>>>>>>>>>>>>> 2G POs to #6 and NEG to #4.11 Excessive Large TPS (Throttle Position Sensor) output.
- 12 Excessive Small TPS output
- 13 Defective or improperly adjusted TPS
- 14 TPS adjusted improperly
- 15 Open circuited low-oil-temp sensor <1992 and 1993>
- 16 Short Circuited High -oil-temp-sensor <1992 only>
- 17 open circuited high temp sensor or short circuited low oil-temp-sensor <1992 only>
- 21 Open-Circuited Kickdown Servo
- 22 Short-circuited Kickdown Servo
- 23 Open-Circuited Ignition pulse pickup cable
- 24 Open-Circuited or improperly adjusted accelerator switch <1992 Only>
******************** ************************************************** *
- 31 Open-Circuited pulse generator A
- 32 Open-Circuited pulse generator B
- 41 Open-Circuited shift control solenoid valve A
- 42 Short -Circuited shift control solenoid valve A
- 43 Open-Circuited shift control solenoid valve B
- 44 Short-circuited shift control solenoid valve B
- 45 Open-Circuited shift control Pressure Control Solenoid valve
- 46 Short-circuited shift control Pressure Control Solenoid valve
- 47 Open-Circuited torque converter clutch solenoid
- 48 Short-circuited torque converter clutch solenoid
- 49 Defective torque converter clutch system
******************** ************************************************** *
- 51 1st Gear Incorrect Ratio
- 52 2nd Gear Incorrect Ratio
- 53 3rd Gear Incorrect Ratio
- 54 4th Gear Incorrect Ratio
- 61 Short or Open-Circuited torque reduction request or execution signal line
- 62 Open-circuited torque reduction request line
- 63 Short-circuited torque reduction execution line
******************** ************************************************** *
- 81 Open-circuited Pulse Generator A
- 82 Open-circuited Pulse Generator B
- 83 Open or Short-circuited Shift Control Solenoid valve A
- 84 Open or Short-circuited Shift Control Solenoid valve B
- 85 Open or Short-circuited Pressure Control Solenoid valve
- 86 Incorrect gear ratio
Actions: Things to check что проверять
- Codes (11-14)
Check TPS Connector
Adjust TPS
Check TPS
Check accelerator switch (Code 24)
- Codes (15-17)
Check Oil Temp. Sensor Connector
Check Oil Temp. sensor on bench
- Codes (21,22)
Check Kickdown servo switch connector and Kickdown switch on bench
- Code (23)
Check Ignition Pulse Signal Line.
- Code (24)
Check & Adjust Accelerator Switch & Connector
- Codes (31,32)
Check Pulse Generator A or B
Check vehicle reed switch (chattering)
- Codes (41,42)
Check Solenoid Valve connector
Check Shift control solenoid valve A
- Codes (43,44)
Check Solenoid Valve connector
Check Shift control solenoid valve B
- Codes (45,46)
Check Solenoid Valve connector
Check Pressure Control Solenoid Valve
- Codes (47,48)
Check Solenoid Valve connector
Check Torque Converter Clutch Solenoid
- Code (49)
Check Torque Converter Clutch Hydraulic Unit
Check Torque Converter Clutch Solenoid
Replace Control Unit
- Code (51)
Check Connectors of Pulse Generators A and B and the generators themselves
Rear Clutch Slipping
- Code (52)
Check Connectors of Pulse Generators A and B and the generators themselves
Rear Clutch Slipping
Kickdown Brake Slipping
- Code (53)
Check Connectors of Pulse Generators A and B and the generators themselves
Front Clutch Slipping
Rear Clutch Slipping
- Code (54)
Check Connectors of Pulse Generators A and B and the generators themselves
End Clutch Slipping
Kickdown Brake Slipping
- Code (61)
Check Torque Reduction Request Signal Line
Check Torque Reduction Execution Signal Line
- Code (62)
Check Torque Reduction Request Signal Line
- Code (63)
Check Torque Reduction Execution Signal Line
- Code (81) See related code (31)
- Code (82) See related code (32)
- Code (83) See related codes (41,42
- Code (84) See related codes (43,44)
- Code (85) See related codes (45,46)
- Code (86) See related codes (51,52,53,54)